DRK-07B Respirator Flame Retardant Gwajin Aiki Manual
Takaitaccen Bayani:
Gargadi na aminci Ya ku masu amfani Lura cewa abubuwa masu zuwa na iya shiga cikin tsarin amfani da kayan aikin: 1. Da fatan za a tabbatar da karanta ƙa'idodi masu dacewa da umarnin kayan aiki kafin amfani da kayan aiki 2. Dole ne a rufe taga kallo lokacin da gwajin ya kasance ana kai!3. Lokacin da aka yi amfani da ƙayyadaddun ƙarfin lantarki, ƙarfin kayan aiki ya kamata a ƙasa.4. Kayayyakin da ke da kumburi da fashewa banda waɗanda ake buƙata don gwajin an hana su a cikin dakin gwaje-gwaje!...
Gargadi na aminci
Ya ku masu amfani
Lura cewa abubuwa masu zuwa suna iya shiga cikin tsarin amfani da kayan aikin:
1. Da fatan za a tabbatar da karanta ƙa'idodi masu dacewa da umarnin kayan aiki kafin amfani da kayan aiki
2. Dole ne a rufe taga kallo lokacin da gwajin ke ci gaba!
3. Lokacin da aka yi amfani da ƙayyadaddun ƙarfin lantarki, ƙarfin kayan aiki ya kamata a ƙasa.
4. Abubuwan da ke ƙonewa da fashewa banda waɗanda ake buƙata don gwajin an hana su a cikin dakin gwaje-gwaje!
5. Mai aiki ba zai bar wurin gwajin ba.
6. The dakin gwaje-gwaje za a sanye take da kayan kashe gobara.
7. A ƙarshen gwajin, ya kamata a kashe duk hanyoyin wuta da iska.Da fatan za a tabbatar da tsaftace ragowar gwajin ko zubarwa!
Dubawa
An ƙera na'urar gwajin zafin wuta don na'urar numfashi bisa ga gb2626 kayan kariya na numfashi, wanda ake amfani da shi don gwada juriyar wuta da aikin hana wuta na numfashi.Abubuwan da ake amfani da su sune: gb2626 labaran kariya na numfashi, gb19082 buƙatun fasaha don zubar da kayan kariya na likita, gb19083 buƙatun fasaha don abin rufe fuska na likita, da ƙayyadaddun fasaha na gb32610 don abin rufe fuska na yau da kullun Yy0469 abin rufe fuska na likitanci, Yyt0969 abin rufe fuska na likita, da sauransu.
Siffofin fasaha
1. Ana yin gyare-gyaren mashin mask da kayan ƙarfe, kuma an kwatanta fasalin fuska bisa ga rabo na 1: 1.
2. PLC touch allon + PLC iko, don cimma iko / gano / lissafi / bayanai nuni / tarihi data tambaya Multi-aiki.
3. Allon taɓawa:
a.Girman: 7 " Girman nuni mai tasiri: 15.41cm tsawo da 8.59cm fadi;
b.Saukewa: 480*480
c.Sadarwar sadarwa: RS232, 3.3V CMOS ko TTL, yanayin tashar tashar jiragen ruwa
d.Yawan ajiya: 1g
e.Amfani da tsantsar nunin tuƙi na FPGA na kayan masarufi, lokacin farawa "sifili", kunna wuta na iya aiki
f.Yin amfani da m3 + FPGA gine, m3 yana da alhakin rarraba koyarwa, FPGA yana mai da hankali kan nunin TFT don tabbatar da sauri da aminci.
4. Za'a iya daidaita tsayin mai ƙonawa
5. Matsayin atomatik da lokaci
6. Nuna lokacin ƙonewa
7. An sanye shi da firikwensin harshen wuta
8. Gudun motsi na kai (60 ± 5) mm / s
9. Diamita na binciken zafin harshen wuta shine 1.5mm
10. Matsakaicin daidaitawar zafin wuta: 750-950 ℃
11. Daidaiton lokacin ƙonawa shine 0.1s
12. Wutar lantarki: 220 V, 50 Hz
13. Gas: propane ko LPG
Gabatarwa zuwa aikin dubawa
Gwajin dubawa:
1. Danna kai tsaye zuwa saman fitilar don daidaita nisa daga bututun ƙarfe zuwa ƙananan mutu
2. Farawa: gashin kansa ya fara motsawa zuwa hanyar busa wuta kuma ya tsaya a wani wuri ta hanyar hurawa.
3. Ƙarfafawa: kunna / kashe fankar shaye-shaye akan akwatin →
4. Gas: bude / rufe tashar gas
5. Ignition: fara babban na'urar kunna wuta
6. Haske: kunna / kashe fitilar a cikin akwatin
7. Ajiye: adana bayanan gwajin bayan gwajin
8. Lokaci: rubuta lokacin konawa
Uhanyar sage
Tukwici: da fatan za a karanta ƙa'idodin gwajin da suka dace a hankali kafin amfani da kayan aiki!
1. Haɗa wutar lantarki da tushen iska a bayan akwatin
2. Kunna wutar lantarki kuma tura sama da ƙulli a gaban panel (an nuna matsayi a cikin hoton da ke ƙasa)
Bayan kunnawa, shigar da ƙirar gwaji
a.Da farko, danna maɓallin daidaitawa matsayi, kuma ƙirar kai ta fara motsawa.Lokacin da ƙyallen kai ya hango firikwensin matsayi na harshen wuta, ƙirar kan ta daina motsi;a wannan lokacin, da hannu daidaita nisa tsakanin busa wuta da ƙananan ƙarshen mashin zuwa 20 mm, sa'an nan kuma gyara matsayi na hurawa.
b.Daidaita matsayin hurawa sannan danna fara don sake saita tsarin kai
c.Bayan an sake saita ƙirar kai, danna maɓallin gas don kunna gas ɗin, sannan danna maɓallin kunnawa.Mai kunna wuta zai kunna wuta sau uku.Idan ba a kunna ba, sake danna maɓallin kunnawa
d.nuna mai ƙonawa kuma daidaita kullin iskar gas akan panel don yin tsayin harshen 40 + 4mm.
e.Bayan daidaita tsayin harshen wuta, ana amfani da firikwensin zafin jiki don auna zafin jiki a 20 ± 2mm akan hurawa.Ana daidaita zafin jiki na harshen wuta zuwa 800 ± 50 ℃ ta hanyar daidaita goro a ƙananan ƙarshen mai ƙonawa (an nuna matsayi a cikin hoton da ke ƙasa) tare da iska.
f.Bayan daidaita zafin jiki, cire firikwensin zafin jiki, danna maɓallin farawa, kuma ƙirar kai ta fara motsawa kamar sauran ƙarshen.
g.Lokacin da firikwensin matsayi na harshen wuta ya gano ƙirar kansa, lokacin bayan konawa yana kan lokaci ta atomatik.Lokacin da ci gaba da konewa (jimlar lokacin ƙonewa da ƙonewa mara wuta) na abin rufe fuska, danna maɓallin lokaci don dakatar da lokaci.
h.Kuna iya yin alamu guda uku a jere, sannan danna maɓallin Ajiye don adana bayanan
Sauran
1. Ana iya tambayar bayanan da aka adana a cikin bayanan tarihi
2. Yayin gwajin, ana iya kunna ko kashe fitilar kamar yadda ake buƙata
3. Bayan gwajin, kunna iska mai shayarwa don sharar iskar gas ɗin konewa daga akwatin
4. Ko sakamakon gwajin ya cancanta ana iya kwatanta shi bisa ga ka'idoji ko ka'idoji
