DRK-681 Flex Durability Tester Aiki Manual

1.Dubawa

Ma'aunin ma'auni da kayan sarrafawa (wanda ake kira da aunawa da kayan sarrafawa) yana ɗaukar sabon tsarin da aka saka ARM, 800X480 babban nunin launi na LCD taɓawa, amplifiers, masu canza A/D da sauran na'urori suna ɗaukar sabuwar fasaha, tare da babban madaidaici kuma babba Halayen ƙuduri, ƙirar sarrafa microcomputer analog, aiki mai sauƙi da dacewa, haɓaka ingantaccen gwajin gwaji.Ayyukan kwanciyar hankali, cikakkun ayyuka, ƙirar tana ɗaukar tsarin kariya da yawa (kariyar software da kariyar kayan aiki), mafi aminci da aminci.

2.Main Technical Parameters 

 Nau'in Gwaji:

(1) Model A (Hanyar 155mm, Angle440 C, Lokacin 2700)

(2) Model B (Hanyar 155mm, Angle440 C, Lokacin 900)

(3) Model C (Hanyar 155mm, Angle440 C, Lokacin 270)

(4) Model D (Hanyar 155mm, Angle440 C, Lokaci 20)

(5) Model E (Hanyar 80mm, Angle400 C, Lokaci 20)

(6) Nau'in Gwaji (Hanyar 155mm, Angle440 C, Daidaitaccen Lokaci)

3.Basic Aiki

Gabatarwar Interface

(Kamar yadda aka nuna a cikin adadi, babban gwajin gwajin ya kasu kashi da yawa kamar yankin menu, wurin nunin kayan gwaji, yankin maɓallin sarrafawa, da wurin nunin lokacin gwaji.)

1.Button aiki

Lokacin da kuke buƙatar yin wani aiki, zaku iya taɓa maɓallin da ya dace kai tsaye da yatsan ku.Idan ka sarrafa motar don dawowa, taɓa maɓallin "Komawa" da yatsa, motar Route da motar torsion suna dawowa lokaci guda, kuma wurin nuna halin gwaji yana nuna kalmar "Komawa".

2. Yanayin zaɓi

Taɓa menu mai dacewa a cikin yanayin zaɓin yanayin don aiwatar da aikin da ya dace.Idan ka taɓa maɓallin "yanayin zaɓi", menu na zaɓin yanayin zai tashi, kuma zaka iya zaɓar yanayin.Bayan ka zaɓi yanayin gwaji, sunan gwajin da wurin nunin gwaji zai canza daidai;taɓa maɓallin “parameter”, kuma maɓallin shigar da sigina zai tashi>, ana iya aiwatar da saitunan sigina.

3.Shigarwar siga

Lokacin shigar da sigogi, taɓa akwatin shigar da sigina kuma maballin lamba zai tashi.Latsa buƙatar ma'aunin shigarwa akan madannai na lamba kuma taɓa maɓallin lamba daidai don shigar da sigar.Bayan shigar, danna maɓallin "ENT" don kammala shigarwar, wannan shigarwar tana aiki;danna maɓallin "ESC" don soke shigarwar, wannan shigarwar ba ta da inganci.

4.Zaɓin yanayi

A cikin yankin zaɓi na menu, taɓa maɓallin "zaɓin yanayi", menu na zaɓin yanayin zai tashi, kuma za'a iya zaɓar yanayin gwaji.Bayan zaɓar yanayin, sunan gwajin da wurin nunin sakamakon gwaji zai canza daidai.

Hanyoyin gwajin da za a iya zaɓa su ne: yanayin A, yanayin B, yanayin C, yanayin D, yanayin E, yanayin gwaji, da sauransu.

5. Saitin Ma'auni

A cikin, taɓa maɓallin "Parameter" don shigar da.

A cikin, ana iya yin sigogin gwaji da daidaita haske na LCD.

1. Gwajin gwaji:

1) Hanya: Hanyar da aka saita a yanayin gwaji, gabaɗaya 155mm;

2) Angle: kusurwar torsion da aka saita a cikin yanayin gwaji, gabaɗaya digiri 440;

3) Lokuta: Yawan lokutan gwaji da aka saita a yanayin gwaji, wanda za'a iya saita shi ba bisa ka'ida ba;

2. Daidaita haske:

Kamar yadda aka nuna a cikin hoton da ke sama, ana iya daidaita hasken LCD a cikin.Girman ƙimar, mafi girman haske.

6.Tsarin Gwaji

1)Saitin siga

Duba yanayin aiki kafin gwajin, kuma sake saita yanayin idan ya cancanta.

Idan yanayin gwaji ne, hanya, kwana, da Lokacin yanayin gwajin ya kamata a saita a cikin saitunan ma'auni.

2) Shirye-shiryen gwaji

Taɓa maɓallin “Dawowa” don mayar da motar Route da injin torsion zuwa matsayinsu na farko.

Matsa samfurin.

3) Gwaji

Taɓa maɓallin “Gwaji”, Motar Hanya da injin torsion za su yi aiki a mitar gwajin da kayyade ma'auni har sai an kai adadin lokacin da aka saita, kuma gwajin ya ƙare.Motocin biyu suna dawowa ta atomatik.

Bakwai.saita lokaci

7.Time Saitin Lokaci

Taɓa wurin nunin lokaci a ƙasan dama na, kuma saita lokacin tsarin akan maballin lambobi masu tasowa.

8.Buga sakamakon gwaji

A cikin, taɓa maɓallin “Print” don buga sakamakon gwajin.

9.Daidaitawa

A cikin, taɓa maɓallin “Calibration”, kuma shigar da kalmar wucewa zai tashi.Shigar da kalmar wucewa () don shigar da.(Sai dai ma'aikatan metrology na doka, kada ku shiga yanayin daidaitawa yayin amfani da wannan tsarin, in ba haka ba za'a canza ma'aunin ƙididdiga yadda ake so, wanda zai shafi sakamakon gwajin.)

A cikin, za ku iya daidaita ma'aunin hanyoyin hanya da ma'aunin Angle coefficients.Hakanan zaka iya saita Gudun Hanya, Gudun Torsion, da Rabin Lokaci, kuma auna RoutePeriod da Lokacin Torsion..

1) 400 digiri torsion lokaci: (QEI an haɗa zuwa encoder fitarwa na torsion motor direba a lokacin gwajin)

Lokacin da ake ɗauka don karkatar da motar da digiri 400.

Bayan saita saurin torsion, da farko komawa wurin, danna maɓallin "gwajin torsion", kuma injin ɗin zai juya zuwa wani kusurwa sannan ya tsaya.Dubi ainihin kusurwar torsion kuma daidaita wannan ƙimar ta yadda ainihin kusurwar torsion ɗin daidai yake da digiri 400.

2) 440 digiri torsion lokaci: lokacin da ake bukata don mayar da mota zuwa 440 digiri.

Hanyar gwaji ɗaya ce da lokacin karkatar da digiri 400.

3) Lokacin jiran dawowar digiri 400: wannan lokacin shine lokacin jira don dawowa bayan juyawa 400, wanda ake amfani dashi don saduwa da lokacin da ake buƙata na Route 80mm.

4) Digiri na 440 na dawowa lokacin jira: wannan lokacin shine lokacin jira don dawowa bayan juyawa 440, wanda ake amfani dashi don saduwa da lokacin da ake buƙata na Route90mm.

5) Cikakken lokaci da Rabin lokaci: Ana amfani da shi don nuna lokacin cikakken lokaci da rabi yayin gwaje-gwajen Lokaci da Juyi.

6) Saitin Rabin-Lokaci: Wannan ƙimar ita ce lokacin jira bayan kammala tsarin bacin rai, wanda shine rabin cikakken lokaci don saduwa da saitin Lokaci.

7) Gudun hanya, saurin karkatarwa:

Ƙimar bugun bugun jini shine saurin motar Hannu da saurin juzu'i lokacin da RoutePeriod (45/min) ya gamsu.

8) Koma sigogi: Koma Hanyar 1, 2 da saurin dawowa 1, 2, tare da

dawo da aikin Motar Hanyar don sa ƙimar Hanyar ta fi daidai lokacin da motar Hanyar ta tsaya.

Komawa torsion: yi aiki tare da aikin injin torsion don sa ƙimar kusurwa ta fi daidai lokacin da injin torsion ya tsaya.